gpm(8)
NAME
gpm - a cut and paste utility and mouse server for virtual consoles
SYNOPSIS
gpm [ options ]
DESCRIPTION
This package tries to be a useful mouse server for applications running on the Linux console. It is based on the "selection" package, and some of its code comes from selection itself. This package is intended as a replacement for "selection" as a cut-and-paste mechanism; it also provides additional facilities. The "selection" package offered the first cut-and-paste implementation for Linux using two mouse buttons, and the cut buffer is still called "selection buffer" or just "selection" throughout this document. The information below is extracted from the texinfo file, which is the preferred source of information. The `gpm' executable is meant to act like a daemon (thus, `gpmd' would be a better name for it). This section is meant to describe the command-line options for `gpm', while its internals are outlined in the next section. Due to restrictions in the `ioctl(TIOCLINUX)' system call, `gpm' must be run by the superuser. The restrictions have been added in the last 1.1 kernels to fix a security hole related to selection and screen dumping. The server can be configured to match the user's taste, and any application using the mouse will inherit the server's attitude. From release 1.02 up to 1.19.2 is was possible for any user logged on the system console to change the mouse feeling using the -q option. This is no longer possible for security reasons. As of 0.97 the server program puts itself in the background. To kill `gpm' you can just reinvoke it with the `-k' cmdline switch, although `killall gpm' can be a better choice.
SPECIAL COMMANDS
Version 1.10 adds the capability to execute special commands on certain
circumstances. Special commands default to rebooting and halting the
system, but the user can specify his/her personal choice. The
capability to invoke commands using the mouse is a handy one for
programmers, because it allows to issue a clean shutdown when the
keyboard is locked and no network is available to restore the system to
a sane state.
Special commands are toggled by triple-clicking the left and right
button -- an unlikely event during normal mouse usage. The easiest way
to triple-click is pressing one of the buttons and triple-click the
other one. When special processing is toggled, a message appears on the
console (and the speaker beeps twice, if you have a speaker); if the
user releases all the buttons and presses one of them again within
three seconds, then the special command corresponding to the button is
executed.
The default special commands are:
left button
Reboot the system by signalling the init process
middle button (if any)
Execute `/sbin/shutdown -h now'
right button
Execute `/sbin/shutdown -r now'
The `-S' command line switch enables special command processing and
allows to change the three special commands. To accept the default
commands use `-S ""' (i.e., specify an empty argument). To specify
your own commands, use a colon-separated list to specify commands
associated to the left, middle and right button. If any of the commands
is empty, it is interpreted as `send a signal to the init process'.
This particular operation is supported, in addition to executing
external commands, because sometimes bad bugs put the system to the
impossibility to fork; in these rare case the programmer should be able
to shutdown the system anyways, and killing init from a running process
is the only way to do it.
As an example, `-S ":telinit 1:/sbin/halt"', associates killing init to
the left button, going single user to the middle one, and halting the
system to the right button.
System administrators should obviously be careful about special
commands, as gpm runs with superuser permissions. Special commands are
best suited for computers whose mouse can be physically accessed only
by trusted people.
COMMAND LINE OPTIONS
Available command line options are the following:
-a accel
Set the acceleration value used when a single motion event is
longer than delta (see `-d').
-A[limit]
Start up with selection pasting disabled. This is intended as a
security measure; a plausible attack on a system seems to be to
stuff a nasty shell command into the selection buffer (`rm -rf
/') including the terminating line break, then all the victim
has to do is click the middle mouse button .. As of version
1.17.2, this has developed into a more general aging mechanism;
the gpm daemon can disable (age) selection pasting automatically
after a period of inactivity. To enable this mode just give the
optional limit parameter (no space in between !) which is
interpreted as the time in seconds for which a selection is
considered valid and pastable. As of version 1.15.7, a trivial
program called `disable-paste' is provided. The following makes
a good addition to `/etc/profile' if you allow multiple users to
work on your console.
`case $( /usr/bin/tty ) in
/dev/tty[0-9]*) /usr/bin/disable-paste ;;
esac'
-b baud
Set the baud rate.
-B sequence
Set the button sequence. `123' is the normal sequence, `321' can
be used by left-handed people, and `132' can be useful with two-
button mice (especially within Emacs). All the button
permutations are allowable.
-d delta
Set the delta value. When a single motion event is longer than
delta, accel is used as a multiplying factor. (Must be 2 or
above)
-D Do not automatically enter background operation when started,
and log messages to the standard error stream, not the syslog
mechanism. This is useful for debugging; in previous releases
it was done with a compile-time option.
-g number
With glidepoint devices, emulate the specified button with
tapping. number must be `1', `2', or `3', and refers to the
button number before the `-B' button remapping is performed.
This option applies to the mman and ps2 decoding. No button is
emulated by default because the ps2 tapping is incompatible with
some normal ps2 mice
-h Print a summary of command line options.
-i interval
Set interval to be used as an upper time limit for multiple
clicks. If the interval between button-up and button-down events
is less than limit, the press is considered a double or triple
click. Time is in milliseconds.
-k Kill a running gpm. This can be used by busmouse users to kill
gpm before running X (unless they use `-R' or the single-open
limitation is removed from the kernel).
-l charset
Choose the `inword()' look up table. The charset argument is a
list of characters. `-' is used to specify a range and `\ ' is
used to escape the next character or to provide octal codes.
Only visible character can appear in charset because control
characters can't appear in text-mode video memory, whence
selection is cut.
-m filename
Choose the mouse file to open. Must be before -t and -o.
-M Enable multiple mode. The daemon will read two different mouse
devices. Any subsequent option will refer to the second device,
while any preceding option will be used for the first device.
This option automatically forces the repeater (`-R') option on.
-o list-of-extra-options
The option works similary to the ``-o'' option of mount; it is
used to specify a list of ``extra options'' that are specific to
each mouse type. The list is comma-separated. The options `dtr',
`rts' or `both' are used by the serial initialization to toggle
the modem lines like, compatibly with earlier gpm versions; note
however that using -o dtr associated with non-plain-serial mouse
types may now generate an error. And by the way, use -o after
-m and after -t.
-p Forces the pointer to be visible while selecting. This is the
behaviour of `selection-1.7', but it is sometimes confusing.
The default is not to show the pointer, which can be confusing
as well.
-r number
Set the responsiveness as a percentage of motion (1 to 100,
default 10). A lower number can be used to slow down cursor
motion, this can not be used to make a mouse move faster, see
`-a'.
-R[name]
Causes `gpm' to act as a repeater: any mouse data received while
in graphic mode will be produced on the fifo `/dev/gpmdata' in
protocol name, given as an optional argument (no space in
between !). In principle, you can use the same names as for the
`-t' option, although repeating into some protocols may not be
implemented for a while. In addition, you can specify `raw' as
the name, to repeat the mouse data byte by byte, without any
protocol translation. If name is omitted, it defaults to `msc'.
Using gpm in repeater mode, you can configure the X server to
use its fifo as a mouse device. This option is useful for bus-
mouse owners to override the single-open limitation. It is also
an easy way to manage those stupid dual-mode mice which force
you to keep the middle button down while changing video mode.
The option is forced on by the `-M' option.
-s number
Set the sample rate for the mouse device.
-S commands
Enable special-command processing, and optionally specify custom
commands as a colon-separated list. See above for a detailed
description of special commands.
-t name
Set the mouse type. Use `-t help' to get a list of allowable
types. Use -t after you selected the mouse device with -m.
-v Print version information and exit.
-2 Force two buttons. This means that the middle button, if any,
will be taken as it was the right one.
-3 Force three buttons. By default the mouse is considered to be a
2-buttons one, until the middle button is pressed. If three
buttons are there, the right one is used to extend the
selection, and the middle one is used to paste it. Beware: if
you use the `-3' option with a 2-buttons mouse, you won't be
able to paste the selection.
OPERATION
To select text press the left mouse button and drag the mouse. To paste text in the same or another console, press the middle button. The right button is used to extend the selection, like in `xterm'. Two-button mice use the right button to paste text. Double and triple clicks select whole word and whole lines. Use of the `-p' option is recommended for best visual feedback. If a trailing space after the contents of a line is highlighted, and if there is no other text on the remainder of the line, the rest of the line will be selected automatically. If a number of lines are selected, highlighted trailing spaces on each line will be removed from the selection buffer. Any output on the virtual console holding the selection will clear the highlighted selection from the screen, to maintain integrity of the display, although the contents of the paste buffer will be unaffected. The selection mechanism is disabled if the controlling virtual console is placed in graphics mode, for example when running X11, and is re- enabled when text mode is resumed. (But see BUGS section below.)
BUGS
The `gpm' server may have problems interacting with X: if your mouse is a single-open device (i.e. a bus mouse), you should kill `gpm' before starting X, or use the `-R' option (see above). To kill `gpm' just invoke `gpm -k'. This problem doesn't apply to serial mice. Two instances of gpm can't run on the same system. If you have two mice use the `-M' option (see above). While the current console is in graphic mode, `gpm' sleeps until text mode is back (unless `-R' is used). Thus, it won't reply to clients. Anyways, it is unlikely that mouse-eager clients will spur out in hidden consoles. The clients shipped out with gpm are not updated, thus there are potential security risks when using them.
AUTHORS
Andrew Haylett <ajh@gec-mrc.co.uk> (the original selection code) Ian Zimmerman <itz@speakeasy.org> (old maintainer) Alessandro Rubini <rubini@linux.it> (old maintainer (still helps a lot)) Nico Schottelius <nico@schottelius.org> (maintainer) Many many contributors, to both selection and gpm.
MAINTAINERS
The current maintainer is Nico Schottelius. But without the help of Alessandro Rubini and the mailing list it would be impossible for me to maintain gpm. The development mailing list can be reached under gpm@lists.linux.it. More information on the list is in the README file part of the source distribution of gpm.
FILES
/var/run/gpm.pid The PID of the running gpm /dev/gpmctl A control socket for clients /dev/gpmdata The fifo written to by a repeater (`-R') daemon.
SEE ALSO
gpm-types(7) Description of current pointer types supported by gpm
The info file about `gpm', which gives more complete information and
explains how to write a gpm client.
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
