CONOP3 - sets option switches and specifys various REAL parameters to be used by the Conran_family utility.
CALL CONOP3 (IOPT, ARRAY, LENA)
IOPT Character, input -- Selects an internal parameter and sets an option switch. The possibilities are: 'CHL=ON' or 'CHL=OFF' 'CIL=ON' or 'CIL=OFF' 'CON=ON' or 'CON=OFF' 'DBP=ON' or 'DBP=OFF' 'SDC=ON' or 'SDC=OFF' 'SLD=ON' or 'SLD=OFF' 'TEN=ON' or 'TEN=OFF' ARRAY Real array, input -- Sets an internal parameter. LENA Integer, input -- The length of array ARRAY. If an option is turned 'ON', then the remaining CONOP3 arguments can be used to override the default settings of that option. If the option is 'OFF', then the remaining arguments of the CONOP3 call can be any dummy values. Option settings will be returned to their default values. The following options are defined by this subroutine: CHL This parameter determines how the high and low contour values are set. These contour values may be set by the program or by the user. If CHL=OFF, the program examines the user's input data and determines both the high and low values. If CHL=ON, the user must specify the desired high (HI) and low (FLO) values. The default is CHL=OFF. If program set: CALL CONOP3('CHL=OFF',0.,0) If user set: CALL CONOP3('CHL=ON',ARRAY,2) where ARRAY(1)=HI, ARRAY(2)=FLO Note: The values supplied for contour increment and contour high and low values assume unscaled data values. See the SDC parameter, below. CIL This parameter determines how the contour increment (CINC) is set. The increment is either calculated by the program (CIL=OFF) using the range of high and low values from the user's input data, or set by the user (CIL=ON). The default is CIL=OFF. If program set: CALL CONOP3('CIL=OFF',0.,0) If user set: CALL CONOP3('CIL=ON',CINC,1) Note: By default, ('CIL=OFF') the program will examine the user's input data and determine the contour interval (CINC) at some appropriate range between the level of high and low values supplied, usually generating between 15 and 20 contour levels. Example: CALL CONOP3('CIL=ON',10.,1) will generate contours at increments of 10. units in user coordinates. CON This parameter determines how the contour levels are set. If CON=ON, the user must specify an array of contour values and the number of contour levels. A maximum of NCL=30 contour levels is permitted. If CON=OFF, NCL and the contour values are computed. The default is OFF. If program set: CALL CONOP3('CON=OFF',0.,0) If user set: CALL CONOP3('CON=ON',ARRAY,NCL) Note: The real array (ARRAY) must have the contour levels ordered from smallest to largest. Warning: It is illegal to use the CON option when either CIL or CHL are activated. If this is done, the option call that detected the error will not be executed. DBP This parameter determines how the dash pattern break point (BP) is set. (Does not apply to entry CONRAQ.) If DBP=ON, BP must be set by the user. If DBP=OFF, the program will set BP to 0. This is the default. If program set: CALL CONOP3('DBP=OFF',0.,0) If user set: CALL CONOP3('DBP=ON',BP,1) Note: BP is a floating point number where the break for GTR and LSS contour dash patterns are defined. BP is assumed to be given relative to the untransformed contours. To see how various dash line patterns can be assigned to various contours see parameter DBP in "man conop4". SDC The parameter to determine how to scale the input data from which the contours are generated. (Does not apply to entry CONRAQ.) If SDC=ON, the scaling factor is set to ARRAY(1). If SDC=OFF, the default scale factor of 1. is used. If program set: CALL CONOP3('SDC=OFF',0.,0) If user set: CALL CONOP3('SDC=ON',ARRAY,1) Note: The data plotted on contour lines and the data plotted for relative minimums and maximums will be scaled by ARRAY. SLD Input a polygon to define the extent of area to be contoured. (Does not apply to entry CONRAQ.) When this option is activated, only those contours within the shield are drawn. The shield is a polygon specified by the user which must be given in the same coordinate range as the the data. It must define only one polygon. To input a shield: CALL CONOP3('SLD=ON',ARRAY,LENA) Otherwise: CALL CONOP3('SLD=OFF',0.,0) Note: ARRAY is a real array LENA elements long. The first LENA/2 elements are X coordinates and the second LENA/2 elements are Y coordinates. This polygon must be closed, that is the first and last points in ARRAY must be the same. Example: DIMENSION SHLD(10) DATA SHLD/ 7.,10.,10.,7.,7., 1 7.,7.,10.,10.,7./ CALL CONOP3 ('SLD=ON',SHLD,10) TEN The parameter to determine the tension factor applied when smoothing contour lines using splines under tension. (Does not apply to entry CONRAQ.) If user set, the allowed range is from greater than zero to 30. The higher the tension the less smoothing occurs. The default value (TEN=OFF) is 2.5. If program set: CALL CONOP3('TEN=OFF',0.,0) If user set: CALL CONOP3('TEN=ON',TENS,1) Note: This option is not available in the standard version of CONRAN.
CONOP3 is called to set parameters of type REAL before CONRAN, CONRAQ, or CONRAS are called to generate the contour plot.
Use the command ncargex to see the following examples: tconaq, tconan, and tconas.
To use CONOP3 load the NCAR Graphics libraries ncarg, ncarg_gks, and ncarg_c, preferably in that order.
See the conran_family man page for a description of all Conran_family error messages and/or informational messages.
Online: conran_family, conran_family_params, conran, conraq, conras, conop1, conop2, conop4, conpack, conpack_params Hardcopy: NCAR Graphics Contouring and Mapping Tutorial; NCAR Graphics Fundamentals, UNIX Version; User's Guide for NCAR GKS-0A Graphics
Copyright (C) 1987-2009 University Corporation for Atmospheric Research The use of this Software is governed by a License Agreement.
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.