ping6(8)
NAME
ping, ping6 - send ICMP ECHO_REQUEST to network hosts
SYNOPSIS
ping [-aAbBdDfhLnOqrRUvV6] [-c count] [-F flowlabel] [-i interval] [-I interface] [-l preload] [-m mark] [-M pmtudisc_option] [-N nodeinfo_option] [-w deadline] [-W timeout] [-p pattern] [-Q tos] [-s packetsize] [-S sndbuf] [-t ttl] [-T timestamp option] [hop ...] destination
DESCRIPTION
ping uses the ICMP protocol's mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (``pings'') have an IP and ICMP header, followed by a struct timeval and then an arbitrary number of ``pad'' bytes used to fill out the packet. ping6 is IPv6 version of ping, and can also send Node Information Queries (RFC4620). Intermediate hops may not be allowed, because IPv6 source routing was deprecated (RFC5095).
OPTIONS
-a Audible ping.
-A Adaptive ping. Interpacket interval adapts to round-trip time,
so that effectively not more than one (or more, if preload is
set) unanswered probe is present in the network. Minimal
interval is 200msec for not super-user. On networks with low
rtt this mode is essentially equivalent to flood mode.
-b Allow pinging a broadcast address.
-B Do not allow ping to change source address of probes. The
address is bound to one selected when ping starts.
-c count
Stop after sending count ECHO_REQUEST packets. With deadline
option, ping waits for count ECHO_REPLY packets, until the
timeout expires.
-d Set the SO_DEBUG option on the socket being used. Essentially,
this socket option is not used by Linux kernel.
-D Print timestamp (unix time + microseconds as in gettimeofday)
before each line.
-f Flood ping. For every ECHO_REQUEST sent a period ``.'' is
printed, while for ever ECHO_REPLY received a backspace is
printed. This provides a rapid display of how many packets are
being dropped. If interval is not given, it sets interval to
zero and outputs packets as fast as they come back or one
hundred times per second, whichever is more. Only the super-
user may use this option with zero interval.
-F flow label
ping6 only. Allocate and set 20 bit flow label (in hex) on echo
request packets. If value is zero, kernel allocates random flow
label.
-h Show help.
-i interval
Wait interval seconds between sending each packet. The default
is to wait for one second between each packet normally, or not
to wait in flood mode. Only super-user may set interval to
values less 0.2 seconds.
-I interface
interface is either an address, or an interface name. If
interface is an address, it sets source address to specified
interface address. If interface in an interface name, it sets
source interface to specified interface. For ping6, when doing
ping to a link-local scope address, link specification (by the
'%'-notation in destination, or by this option) is required.
-l preload
If preload is specified, ping sends that many packets not
waiting for reply. Only the super-user may select preload more
than 3.
-L Suppress loopback of multicast packets. This flag only applies
if the ping destination is a multicast address.
-m mark
use mark to tag the packets going out. This is useful for
variety of reasons within the kernel such as using policy
routing to select specific outbound processing.
-M pmtudisc_opt
Select Path MTU Discovery strategy. pmtudisc_option may be
either do (prohibit fragmentation, even local one), want (do
PMTU discovery, fragment locally when packet size is large), or
dont (do not set DF flag).
-N nodeinfo_option
ping6 only. Send ICMPv6 Node Information Queries (RFC4620),
instead of Echo Request. CAP_NET_RAW capability is required.
help Show help for NI support.
name Queries for Node Names.
ipv6 Queries for IPv6 Addresses. There are several IPv6
specific flags.
ipv6-global
Request IPv6 global-scope addresses.
ipv6-sitelocal
Request IPv6 site-local addresses.
ipv6-linklocal
Request IPv6 link-local addresses.
ipv6-all
Request IPv6 addresses on other interfaces.
ipv4 Queries for IPv4 Addresses. There is one IPv4 specific
flag.
ipv4-all
Request IPv4 addresses on other interfaces.
subject-ipv6=ipv6addr
IPv6 subject address.
subject-ipv4=ipv4addr
IPv4 subject address.
subject-name=nodename
Subject name. If it contains more than one dot, fully-
qualified domain name is assumed.
subject-fqdn=nodename
Subject name. Fully-qualified domain name is always
assumed.
-n Numeric output only. No attempt will be made to lookup symbolic
names for host addresses.
-O Report outstanding ICMP ECHO reply before sending next packet.
This is useful together with the timestamp -D to log output to a
diagnostic file and search for missing answers.
-p pattern
You may specify up to 16 ``pad'' bytes to fill out the packet
you send. This is useful for diagnosing data-dependent problems
in a network. For example, -p ff will cause the sent packet to
be filled with all ones.
-q Quiet output. Nothing is displayed except the summary lines at
startup time and when finished.
-Q tos Set Quality of Service -related bits in ICMP datagrams. tos can
be decimal (ping only) or hex number.
In RFC2474, these fields are interpreted as 8-bit Differentiated
Services (DS), consisting of: bits 0-1 (2 lowest bits) of
separate data, and bits 2-7 (highest 6 bits) of Differentiated
Services Codepoint (DSCP). In RFC2481 and RFC3168, bits 0-1 are
used for ECN.
Historically (RFC1349, obsoleted by RFC2474), these were
interpreted as: bit 0 (lowest bit) for reserved (currently being
redefined as congestion control), 1-4 for Type of Service and
bits 5-7 (highest bits) for Precedence.
-r Bypass the normal routing tables and send directly to a host on
an attached interface. If the host is not on a directly-
attached network, an error is returned. This option can be used
to ping a local host through an interface that has no route
through it provided the option -I is also used.
-R ping only. Record route. Includes the RECORD_ROUTE option in
the ECHO_REQUEST packet and displays the route buffer on
returned packets. Note that the IP header is only large enough
for nine such routes. Many hosts ignore or discard this option.
-s packetsize
Specifies the number of data bytes to be sent. The default is
56, which translates into 64 ICMP data bytes when combined with
the 8 bytes of ICMP header data.
-S sndbuf
Set socket sndbuf. If not specified, it is selected to buffer
not more than one packet.
-t ttl ping only. Set the IP Time to Live.
-T timestamp option
Set special IP timestamp options. timestamp option may be
either tsonly (only timestamps), tsandaddr (timestamps and
addresses) or tsprespec host1 [host2 [host3 [host4]]] (timestamp
prespecified hops).
-U Print full user-to-user latency (the old behaviour). Normally
ping prints network round trip time, which can be different f.e.
due to DNS failures.
-v Verbose output.
-V Show version and exit.
-w deadline
Specify a timeout, in seconds, before ping exits regardless of
how many packets have been sent or received. In this case ping
does not stop after count packet are sent, it waits either for
deadline expire or until count probes are answered or for some
error notification from network.
-W timeout
Time to wait for a response, in seconds. The option affects only
timeout in absence of any responses, otherwise ping waits for
two RTTs.
When using ping for fault isolation, it should first be run on the
local host, to verify that the local network interface is up and
running. Then, hosts and gateways further and further away should be
``pinged''. Round-trip times and packet loss statistics are computed.
If duplicate packets are received, they are not included in the packet
loss calculation, although the round trip time of these packets is used
in calculating the minimum/average/maximum round-trip time numbers.
When the specified number of packets have been sent (and received) or
if the program is terminated with a SIGINT, a brief summary is
displayed. Shorter current statistics can be obtained without
termination of process with signal SIGQUIT.
If ping does not receive any reply packets at all it will exit with
code 1. If a packet count and deadline are both specified, and fewer
than count packets are received by the time the deadline has arrived,
it will also exit with code 1. On other error it exits with code 2.
Otherwise it exits with code 0. This makes it possible to use the exit
code to see if a host is alive or not.
This program is intended for use in network testing, measurement and
management. Because of the load it can impose on the network, it is
unwise to use ping during normal operations or from automated scripts.
ICMP PACKET DETAILS
An IP header without options is 20 bytes. An ICMP ECHO_REQUEST packet contains an additional 8 bytes worth of ICMP header followed by an arbitrary amount of data. When a packetsize is given, this indicated the size of this extra piece of data (the default is 56). Thus the amount of data received inside of an IP packet of type ICMP ECHO_REPLY will always be 8 bytes more than the requested data space (the ICMP header). If the data space is at least of size of struct timeval ping uses the beginning bytes of this space to include a timestamp which it uses in the computation of round trip times. If the data space is shorter, no round trip times are given.
DUPLICATE AND DAMAGED PACKETS
ping will report duplicate and damaged packets. Duplicate packets should never occur, and seem to be caused by inappropriate link-level retransmissions. Duplicates may occur in many situations and are rarely (if ever) a good sign, although the presence of low levels of duplicates may not always be cause for alarm. Damaged packets are obviously serious cause for alarm and often indicate broken hardware somewhere in the ping packet's path (in the network or in the hosts).
TRYING DIFFERENT DATA PATTERNS
The (inter)network layer should never treat packets differently depending on the data contained in the data portion. Unfortunately, data-dependent problems have been known to sneak into networks and remain undetected for long periods of time. In many cases the particular pattern that will have problems is something that doesn't have sufficient ``transitions'', such as all ones or all zeros, or a pattern right at the edge, such as almost all zeros. It isn't necessarily enough to specify a data pattern of all zeros (for example) on the command line because the pattern that is of interest is at the data link level, and the relationship between what you type and what the controllers transmit can be complicated. This means that if you have a data-dependent problem you will probably have to do a lot of testing to find it. If you are lucky, you may manage to find a file that either can't be sent across your network or that takes much longer to transfer than other similar length files. You can then examine this file for repeated patterns that you can test using the -p option of ping.
TTL DETAILS
The TTL value of an IP packet represents the maximum number of IP routers that the packet can go through before being thrown away. In current practice you can expect each router in the Internet to decrement the TTL field by exactly one. The TCP/IP specification states that the TTL field for TCP packets should be set to 60, but many systems use smaller values (4.3 BSD uses 30, 4.2 used 15). The maximum possible value of this field is 255, and most Unix systems set the TTL field of ICMP ECHO_REQUEST packets to 255. This is why you will find you can ``ping'' some hosts, but not reach them with telnet(1) or ftp(1). In normal operation ping prints the TTL value from the packet it receives. When a remote system receives a ping packet, it can do one of three things with the TTL field in its response: · Not change it; this is what Berkeley Unix systems did before the 4.3BSD Tahoe release. In this case the TTL value in the received packet will be 255 minus the number of routers in the round-trip path. · Set it to 255; this is what current Berkeley Unix systems do. In this case the TTL value in the received packet will be 255 minus the number of routers in the path from the remote system to the pinging host. · Set it to some other value. Some machines use the same value for ICMP packets that they use for TCP packets, for example either 30 or 60. Others may use completely wild values.
BUGS
· Many Hosts and Gateways ignore the RECORD_ROUTE option.
· The maximum IP header length is too small for options like
RECORD_ROUTE to be completely useful. There's not much that can be
done about this, however.
· Flood pinging is not recommended in general, and flood pinging the
broadcast address should only be done under very controlled
conditions.
SEE ALSO
netstat(1), ifconfig(8).
HISTORY
The ping command appeared in 4.3BSD. The version described here is its descendant specific to Linux.
SECURITY
ping requires CAP_NET_RAW capability to be executed 1) if the program is used for non-echo queries (See -N option), or 2) if kernel does not support non-raw ICMP sockets, or 3) if the user is not allowed to create an ICMP echo socket. The program may be used as set-uid root.
AVAILABILITY
ping is part of iputils package and the latest versions are available in source form at http://www.skbuff.net/iputils/iputils- current.tar.bz2.
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
