radioclkd(1)
NAME
radioclkd - decode time from radio clock(s) attached to serial port
SYNOPSIS
radioclkd [ -tphv ] device
DESCRIPTION
radioclkd is a simple daemon that decodes the time from a radio clock
device attached to the DCD and/or CTS and/or DSR status lines of serial
port of a computer. It is able to decode the DCF77, MSF and WWVB time
signals. The received time is then sent to ntpd using the shared memory
reference clock driver. The type of time signal being received is
automatically determined. If you have problems getting the program to
work using interrupts, the following command is known to help in many
instances. If this fails you can always fall back to the polling
method.
stty crtscts < /dev/ttyS0
Details on a cheap and easy to make device for receiving these time
signals can be found at
http://www.buzzard.org.uk/jonathan/radioclock.html
OPTIONS
-p, --poll
Poll the serial port for changes of status in the DCD, CTS and
DSR lines rather than use interrupts
-t, --test
Enter test mode printing the length of each pulse and the
decoded time at the end of each minute on stdout. The time is
not sent to ntpd using the shared memory reference clock driver
in this mode.
-h, --help
Print a short synopsis of the command line arguments.
-v, --version
Print the version number and then exit.
CONFIGURATION
Configuration is very simple. Use server 127.127.28.0 in your ntp.conf file for a clock attached to the DCD line, server 127.127.28.1 for a clock attached to the CTS line, and server 127.127.28.2 for a clock attached to the DSR line. You will also want to use a fudge line on the server to change the displayed refid.
CALIBRATION
Due to delays in the propogation of the radio signal, it's processing
by the receiver board and the latency of the operating system the time
decoded by the receiver will be slightly offset from actual UTC.
Typically this delay will be less than 20ms, so unless you are very
fussy about the time, or are using more than one time source, such as a
GPS unit, other radio clock or NTP server on the internet you can
ignore this section.
The basics of the calibration procedure is to determine the average
offset of the radio receiver, and use the time1 fudge factor in
ntp.conf to bring the receiver as close as possible to the real time.
The easiest way of determining the offset of the radio receivers time
is to run it against a reference clock that does not suffer from these
problems. The best reference clock would be a GPS unit. This might be a
GPS unit that you don't wish to dedicate to time keeping, or a borrowed
unit. If this is not possible you could use a stratum 1 server on the
internet.
The method of calibration is quite simple. We attach the calibration
reference clock to the computer and fudge the stratum of our radio
receiver up to say 5. This way we can be sure that ntpd will lock onto
the calibration reference clock. We need to make sure that ntpd is
configured to collect peer statistics so make sure we have some lines
similar to these in ntp.conf
statsdir /var/log/ntpstats/
statistics loopstats peerstats clockstats
filegen peerstats file peerstats type day enable
After that we restart ntpd and leave it running for several hours. We
can then make a copy the peerstats file. The trick is to remove all the
entries before ntpd has come into close aggrement with the calibration
reference clock and then run the peer.awk script in the scripts/stats
directory of the ntp distribution. This will give us a mean offset of
our radio receivers in milliseconds. This can them be converted into
seconds and added to the fudge line in ntp.conf for our receiver.
The final step is to remove the change in stratum level for our
reference clock and restart ntpd. If you move the receiver any
significant distance then you will need to repeat this calibration
step. Across the room or around the current building will be fine, but
if you move it to the next town/city then you will need to recalibrate.
IN USE
The version of ntpd that comes with most Linux distributions does not have the shared memory reference clock driver compiled in by default. This can be identified by checking the logs after ntpd is started. If the shared memory reference clock driver is not compiled in then the logs will contain warnings about the reference clock driver not being recognized. To compile ntpd with the shared memory reference clock driver you must specify the --enable-SHM option when running configure. Neither radioclkd or ntpd ever mark the shared memory segment for deletion. If you stop using the shared memory reference clock driver therefore any shared memory segments will persist until you reboot or manually delete the segment using ipcrm. The segments can be identified as the one with key 0x4e545030, 0x4e545031 or 0x4e545032 using the ipcs command.
BUGS
If you are running a kernel with the PPS kit and have a clock attached to the DCD line you may experience lockups. If you encounter this problem the currently recomended solution is to move the clock to either the CTS or DSR lines.
AUTHOR
This program was written by Jonathan Buzzard <jonathan@buzzard.org.uk> and may be freely distributed under the terms of the GNU General Public License. There is ABSOLUTELY NO WARRANTY for this program.
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
