uisp(1)
NAME
uisp - Micro In-System Programmer for Atmel's AVR MCUs
SYNOPSIS
uisp [OPTION].. -dprog=TYPE -dpart=AT90XXX --FUNCTION.. [if=SOURCE] [of=DEST]
DESCRIPTION
Programming Methods:
-dprog=<method>
avr910 Standard Atmel Serial Programmer/Atmel Low Cost
Programmer
pavr http://www.avr1.org/pavr/pavr.html
stk500 Atmel STK500
dapa Direct AVR Parallel Access
stk200 Parallel Starter Kit STK200, STK300
abb Altera ByteBlasterMV Parallel Port Download Cable
atdh Atmel-ISP Download Cable (P/N ATDH1150VPC)
avrisp Atmel AVR ISP (?)
bsd http://www.bsdhome.com/avrdude/ (parallel)
fbprg http://ln.com.ua/~real/avreal/adapters.html (parallel)
dt006 http://www.dontronics.com/dt006.html (parallel)
maxi Investment Technologies Maxi (parallel)
dm04 Datamekatronik 2004 (parallel)
dasa serial (RESET=RTS SCK=DTR MOSI=TXD MISO=CTS)
dasa2 serial (RESET=!TXD SCK=RTS MOSI=DTR MISO=CTS)
dasa3 serial (RESET=!DTR SCK=RTS MOSI=TXD MISO=CTS)
Target Device Selection:
-dpart=part
Set target abbreviated name or number. For some programmers, if
-dpart is not given programmer's supported devices are listed.
Set -dpart=auto for auto-select. Auto-select does not work with
all programmers, so it is recommended to always specify a target
device explicitly.
Parallel Device Settings:
-dlpt=address|device name
specify device name (Linux ppdev, FreeBSD ppi, serial) or direct
I/O parallel port address (0x378, 0x278, 0x3BC)
-dno-poll
Program without data polling (a little slower)
-dno-retry
Disable retries of program enable command
-dvoltage=value
Set timing specs according to the power supply voltage in [V]
(default 3.0)
-dt_sck=time
Set minimum SCK high/low time in micro-seconds (default 5)
-dt_wd_flash=time
Set FLASH maximum write delay time in micro-seconds
-dt_wd_eeprom=time
Set EEPROM maximum write delay time in micro-seconds
-dt_reset=time
Set reset inactive (high) time in micro-seconds
-dinvert=[sck[,mosi[,miso[,reset]]]]]
Invert specified lines Use -v=3 option to see current settings.
-d89 Allow parallel programming of AT89S51 and AT89S52 devices.
Atmel Low Cost Programmer Serial Device Settings:
-dserial=device name
Set serial interface as /dev/ttyS* (default /dev/avr)
-dspeed=1200|2400|4800|9600|19200|38400|57600|115200
Set speed of the serial interface (default 19200)
Stk500 specific options:
-dhiv Use Hi-V programming instead of SPI (default is SPI).
--rd_aref
Read the ARef Voltage. Note that due to a bug in the stk500
firmware, the read value is sometimes off by 0.1 from the actual
value measured with a volt meter.
--wr_aref=value
Set the ARef Voltage. Valid values are 0.0 to 6.0 volts in 0.1
volt increments. Value can not be larger than the VTarget
value.
--rd_vtg
Read the Vtarget Voltage. Note that due to a bug in the stk500
firmware, the read value is sometimes off by 0.1 from the actual
value measured with a volt meter.
--wr_vtg=value
Set the VTarget Voltage. Valid values are 0.0 to 6.0 volts in
0.1 volt increments. Value can not be smaller than the ARef
value.
--rd_osc
Read the oscillator frequency in Hertz.
--wr_osc=value
Set the oscillator frequency in Hertz, from 14.06 to 3686400.
Functions:
--upload
Upload "input_file" to the AVR memory.
--verify
Verify "input_file" (processed after the --upload opt.)
--download
Download AVR memory to "output_file" or stdout.
--erase
Erase device.
--segment=flash|eeprom|fuse
Set active segment (auto-select for AVA Motorola output)
Fuse/Lock Bit Operations:
--rd_fuses
Read all fuses and print values to stdout
--wr_fuse_l=byte
Write fuse low byte
--wr_fuse_h=byte
Write fuse high byte
--wr_fuse_e=byte
Write fuse extended byte
--wr_lock=byte
Write lock bits. Argument is a byte where each bit is:
Bit5 -> blb12
Bit4 -> blb11
Bit3 -> blb02
Bit2 -> blb01
Bit1 -> lb2
Bit0 -> lb1
--lock Write lock bits [old method; deprecated].
Files:
if=filename
Input file for the --upload and --verify functions in Motorola
S-records (S1 or S2) or 16 bit Intel format
of=filename
Output file for the --download function in Motorola S-records
format, default is standard output
Other Options:
-v=level
Set verbose level (-v equals -v=2, min/max: 0/4, default 1)
--hash=perbytes
Print hash (default is 32 bytes)
--help -h
Help
--version
Print version information
--terminal
Invoke shell-like terminal
AUTHOR
Written by Uros Platise.
REPORTING BUGS
Report bugs to <uisp-dev@nongnu.org>
SEE ALSO
http://savannah.nongnu.org/download/uisp/
COPYRIGHT
(c) 1997-1999 Uros Platise, 2000-2004 Marek Michalkiewicz uisp is free software, covered by the GNU General Public License. You are welcome to change it and/or distribute copies of it under the conditions of the GNU General Public License.
Opportunity
Personal Opportunity - Free software gives you access to billions of dollars of software at no cost. Use this software for your business, personal use or to develop a profitable skill. Access to source code provides access to a level of capabilities/information that companies protect though copyrights. Open source is a core component of the Internet and it is available to you. Leverage the billions of dollars in resources and capabilities to build a career, establish a business or change the world. The potential is endless for those who understand the opportunity.
Business Opportunity - Goldman Sachs, IBM and countless large corporations are leveraging open source to reduce costs, develop products and increase their bottom lines. Learn what these companies know about open source and how open source can give you the advantage.
Free Software
Free Software provides computer programs and capabilities at no cost but more importantly, it provides the freedom to run, edit, contribute to, and share the software. The importance of free software is a matter of access, not price. Software at no cost is a benefit but ownership rights to the software and source code is far more significant.
Free Office Software - The Libre Office suite provides top desktop productivity tools for free. This includes, a word processor, spreadsheet, presentation engine, drawing and flowcharting, database and math applications. Libre Office is available for Linux or Windows.
Free Books
The Free Books Library is a collection of thousands of the most popular public domain books in an online readable format. The collection includes great classical literature and more recent works where the U.S. copyright has expired. These books are yours to read and use without restrictions.
Source Code - Want to change a program or know how it works? Open Source provides the source code for its programs so that anyone can use, modify or learn how to write those programs themselves. Visit the GNU source code repositories to download the source.
Education
Study at Harvard, Stanford or MIT - Open edX provides free online courses from Harvard, MIT, Columbia, UC Berkeley and other top Universities. Hundreds of courses for almost all major subjects and course levels. Open edx also offers some paid courses and selected certifications.
Linux Manual Pages - A man or manual page is a form of software documentation found on Linux/Unix operating systems. Topics covered include computer programs (including library and system calls), formal standards and conventions, and even abstract concepts.
